B90 for Volkswagen and Audi 377.00
Designed to accurately and efficientlyExtract or Install Hubs and Wheel Bearings of spindle assemblies.Applicable: All Front wheel drive VW (Water cooled) and Audifrom early 1970 to present with S.R.W.B. and I.F.S. including A.W.D.Pictures are for reference only. This is the Volkswagen Audi Kit. The Volkswagen kit "only" available below.
read more:

Die Cast 67 Beetle 29.99
1967 Yellow Volkswagen Beetle ... This is a 1:18 scale die cast and plastic reproduction of the 1967 Volkswagen Beetle. The Beetle was considered by most experts as the most desirable of all the Beetles, the 1967 combines the traditional early body design with a larger 1300cc engine and many other mechanical refinements.
read more:

Die Cast 67 Beetle Red 29.99
1967 Red Volkswagen Beetle ... This is a 1:18 scale die cast and plastic reproduction of the 1967 Volkswagen Beetle. The Beetle was considered by most experts as the most desirable of all the Beetles, the 1967 combines the traditional early body design with a larger 1300cc engine and many other mechanical refinements. This reproduction model has, opening hood, opening doors, opening trunk, adjustable front wheels, workable steering, spare tire and adjustable seats.
read more:

Spark Plug Boot Tool 32.99
Spark Plug Boot Tool
Due to restricted space the T10029 will install the spark plug boot properly.
VW and Audi spark plug boots designed to seal and increase contact between the spark plug and spark plug wire.
With the increased seal and location of the boot,
this tool has been made to access and remove the spark plug boot.
Tool is approximately 10 inches (250mm) long.
Used to pull off the spark plug socket...SOME APPLICATIONS INCLUDE: 2.8 2.9L VR6 engines
VW Golf, Corrado and Passat.Also Audi 80, 100, A4, A6 with 2.6 and 2.8L V6 engines.
This is the correct tool for the job.You will most likely find OLD number 3277 or 3277A in your manuals but
T10029 is the CORRECT current Volkswagen Audi Tool number. 3277 is and old number and Volkswagen calls this a SPARK PLUG CONNECTOR TOOL.
read more:

VW428A 49.99
Volkswagen 428a FACTORY TOOL MADE IN GERMANY

In Stock Now!
Call if you need more info on this tool.
read more:

Oil Seal Tool 42.50
Porsche Volkswagen Tool like 204BUsed for proper installationof oil seal on flywheel side of crank shaft. All VW Boxer 4.
read more:

Heavy Duty Bench Clamp 187.50
313 Volkswagen Porsche Tool Designed for to securely carry the full weightof an air cooled twin turbo Boxer 6Tool Number VW 313Properly suited for a work bench.
read more:

Valve Adjustment * Deep Offset Wrench 5.99
German MadeDeep Offset 12 Point Spanner.This Exact item is no longer available from Germany.PORSCHE VW VALVE ADJUSTMENTTYPE 1, 2, 3 and 4 VOLKSWAGEN
read more:

Press tool 401 0.00
High Quality German Made
Volkswagen Press Tool for assembly work.
Original Factory Tool.
read more:

Puller Only 84.00
Puller Same as Volkswagen Tool 3032
Injection Pump ToolUsed for the proper extraction of injection pump drive gear.Applicable:VW Audi diesels *Excluding TDI
read more:

Volkswagen Filler Tool 5.99
NUMBER VW170Tool is for Air Cooled VW repair,and is designed to remove and installthe nut that holds the oil fillerand breather tin to the generator stand. Designed to snap over a 1/2 drive extension,this tool easily reaches down into the oil fill,to remove or tighten the hard to get at retaining nut.
read more:

Hazet Box Made in Germany 149.99
5 Tray Box
530 x 200 x 200mm.
Blue Stove Enameling
Super cool blue Hazet box Made in Germany for the Porsche and Volkswagen enthusiast.
read more:

Flywheel Lock 22.95
215 Volkswagen Porsche Tool
Flywheel Lockused to secure the crankshaft from rotating during R&R of motor.
Used in conjunction with Engine Holding Fixture P201,
where Flywheel Lock bolts into a machined channel.
All Porsche and VW 6V or 12V, air cooled.Please note: This item is included in the complete kit also.
read more:

Pinion Nut Cone 69.50
Like Volkswagen Tool 381/14Pinion Nut Cone Socket Cone shaped Socket with 1/2" drive.This tool is used for R&R of grooved nutwhich retains pinion bearing within its housing.Applicable: Early VW air cooled models.
read more:

36mm Flare Wrench 42.50
Special 36mm Flare Wrench like vw 179.Oil Line 12 Point Wrench for servicing Oil Lineson most 1977 and Later Porsche 911 and 944 Turbo.This tool is also used for adjusting rear suspension heighton 77 and Newer Porsche 911and for camber on most late model Volkswagen Bug.
read more:

Cylinder Head Tool Kit 23.50
Cylinder Head Alignment Kit Same as Volkswagen Tool 3070
Set comes with (2) pairs of guide pins, 11X1.75mm and 12X1.75mm.VW model Scirocco, Rabbit, Dasher, Fox. Audi model 4000, 5000
read more:

Flywheel Lock 00
Universal Flywheel Lock
Designed for use on all air cooled Volkswagen engines
Type 1, 2, 3, & 4 and on all air cooled Porsche engines
(series 356, 912, 914, & all 911s through 1969).
This tool is a must when changing a flywheel or its seal
and it comes in handy when changing a clutch.
Made from a forging, this quality tool will last a lifetime.
read more:

17 x 17 Injection Wrench 39.50
Double Ended Flare Nut Box Wrench Size 17 x 17mmOverall Length 241mm (9.5 inch)For injection pipes on Volkswagen / Audi This tool will help you when you remove and install the fuel lines from the injection pump and the injectors themselves.For TDI: You will still need to torque the 17mm fittings down to spec, but this tool will make taking the fittings off a snap, as well as putting them back on.This is a Factory Tool Made in Germany
read more:

Brake Caliper Rewind Set 47.99
U.S./EURO/ASIAN/4WD VEHICLES
Disc Brake Pad & Caliper Service Tool Kit
Includes 8 adapters Magnetic socket adapter.
For brake assemblies
For rotating pistons back into caliper to provide clearance for new pads
Prevents damage to the piston and bootDesigned for use with Mercedes, BMW, Volkswagen, GM, Audi, Ford,Honda, Subaru, Mazda, Nissan, Mitsubishi, Toyota, Land Rover and 4 wheel drive vehicles.Blow molded carryingcase for easy storage.
read more:

Power Steering Pump/Alternator Pulley Puller 29.50
Power Steering Pump/Alternator Pulley Puller
Removes power steering and alternator pulleys on selected applications of Chrysler, Ford, GM and Volkswagen with hub sizes of 1 1/8", 1 1/4", 1 5/16" and 1 3/8".
read more:

TDI Cam Tools 148.50
Volkswagen ref: T40001
First number 2510 1
Extractor (Puller)for the camshaft phasing gear with 5 and 6 spokes on 4 resp.
6 cylinder engines TDi, engines V6 and V8,
AUDI A 4, A 6, A 8
Second Item 2510 8 Extraction Hook
for the careful extraction of camshaft phasing gear with 5 spokes on VW/AUDI V8 carburetor engines.
Call if you have questions about this item.
read more:

Optical Tester Made in Germany 0.00
Super Optical Tester
Cooling System Special Tool
Hazet 4810 Made in Germany
for controlling the anti freezing acid concentration
in the cooling system, as well as for cooling fluid G11 and G12
VOLKSWAGEN/AUDI and the battery acid concentration (battery charging).
read more: